KD-200

These double-cut shears feed quickly and quietly, without warping or bending your finished piece (distortion is in the waste strip). It easily follows a scribed line. The materials edges are not hardened or burred, so you get maximum use of a sheet. The swiping action of blades seals the edge of coated metals. These shears cut C.R. mild steel up to 18 gauge in straight or contour lines at 180 inches per minute, most grades of stainless and plastic or Formica up to 3/32" thick. These shears are also available with a contour cutting blade KD-200C to cut tighter curves and the HS blade KD-200HS for cutting foam filled doors.

KD-242

These lightweight shears, designed for durability, cut 16 gauge C. R. mild steel and stainless to 18 gauge. Close clearance heavy duty blades provide smooth cutting action, without burring or buckling the material. The aluminum shear head curls the waste strip into a handy coil for fast clean-up, allowing maximum sheet usage. With a straight On/Off switch, the KD-242 fills the gap between Kett light gauge and heavy gauge power shears. Also available in a variable speed model KD-442.

KD-440

This lightweight, pistol-grip shear cuts 14 gauge C.R. mild steel and most grades of stainless to 16 gauge. Double-insulated, the 5 AMP KD-440 cuts at over 150 inches per minute, leaving a clean, flat sheet, ready to fabricate. Distortions are absorbed in an easily disposed of waste curl, leaving the sheet cool and free of burn, chips and burrs. The cutting blades are finest high-speed steel, which you can easily replace.

KD-442

The KD-442 variable speed shear easily cuts through 16 gauge C.R. mild steel and stainless to 18 gauge. The steel shear head has close cutting heavy duty blades that quickly cut through sheet metal, spiral pipe, metal doors and metal studs. Double cutting action provides maximum sheet usage without burring or buckling the material. At less than 5 pounds this KETT shear is both portable for location usage and durable for daily shop operations.

P-1040

A variable speed trigger on this straight handle pneumatic shear, allows smooth, easy starting cuts in C.R. mild steel to 14 gauge and most grades of stainless to 16 gauge. The 7/32" waste curl leaves both sides of the cut straight, with no need to file or de-burr. At 4 pounds and 10" long the P-1040 is lightweight and portable. It features the KETT 2500 RPM power unit designed for maximum efficiency at 90 PSI air pressure.

P-1042

KETT's all-purpose 16 gauge straight handle power shear cuts up to 16 gauge mild steel, cleanly and easily, without burring or buckling the material. Designed for ease and durability, this lightweight pneumatic shear fills the gap between KETT's light-gauge and heavy-gauge power shear lines. The cast aluminum shear housing is now equipped with close-clearance, heavy-duty cutting blades that are essential for handling thin sheet. Thus, the P-1042 is more than capable of shearing through light shim stock and up to 16-gauge steel with the same smooth cutting action. The P-1042 features the Kett 2500 RPM pneumatic power unit designed for maximum efficiency at 90 PSI air pressure. Able to quickly cut through sheet metal, spiral pipe, metal studs and metal doors, and weighing less than 4 pounds, this is truly a portable hand tool that's ideal for fast work in the shop or on the job.

P-1060

The P-1060 Straight Handle Pneumatic Shear features a variable speed push lever control which provides a smooth, well balanced grip. This double-cut shear easily cuts through 18 gauge C.R. mild steel and stainless to 20 gauge, eliminating the need to file or deburr. The P-1060 delivers up to 2500 RPM's when powered by a 90 PSI air source.

P-500

The double-cutting action of the P-500, cleanly cuts 18 gauge and lighter C.R. mild steel without distortion. The 7/32" waste curl leaves both sides of the cut straight with no need to file or de-burr. Variable speed trigger lets you control speed from 0 to 2200 RPM's. The P-500 cuts up to 180 inches per minute. powered by a 90 PSI air power source. Ideal for the tinner, roofer and auto body shop.

P-540

The P-540 takes over where the P-500 leaves off, cutting 14 to 18 gauge in cold rolled steel. Its variable-speed trigger lets you make smooth, easy starting cuts even in most grades of stainless up to 16 gauge. The 4 pound, pistol grip, 2200 RPM pneumatic motor, runs on a 90 PSI power source. A great time-saver in any construction company, sheet metal or sign shop.

P-542

A variable speed trigger allows smooth, easy starting cuts in C.R. mild steel to 16 gauge and most grades of stainless to 18 gauge. The 7/32" waste curl leaves both sides of the cut straight, with no need to file or de-burr. At 3 1/2 pounds and 11" long the P-542 is lightweight and portable. It features the KETT 2200 rpm power unit designed for maximum efficiency at 90 PSI air pressure.